Return to True Weldless Bulkhead - With 1/2" NPT Male Threads

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 5

0 of 0 people found the following review helpful:

June 11, 2024 Reviewer: Alan Crauthers from Hubbard, OR United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Great for HD coolers November 4, 2021 Reviewer: Ryan Mooney from Neptune, NJ United States   I bought this for my 10 gallon Home Depot cooler mash tun to replace the bulkhead that came with the ball valve, which is a threaded tube that is difficult to get a seal on. I had to do some teflon tape olympics along with washers to get it to seal, which I did not foresee holding up over time. For this weldless bulkhead, I also bought a 1/2" male to 1/2" female fitting/extension off of Amazon to prevent the handle from hitting the cooler wall when closed. It gives the perfect amount of extra space to give room for the ball valve handle to completely close, with room for your fingers to fit between the handle and cooler wall. https://www.amazon.com/dp/B0952RPR6K?psc=1&ref=ppx_yo2_dt_b_product_details Was this review helpful to you?

0 of 0 people found the following review helpful:

June 2, 2021 Reviewer: AdrienM from Lafayette, LA United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Excellent Option April 7, 2021 Reviewer: Anonymous Person   I used this on a booler to make an HLT.  Installed easily with no leaks.  Definitely the best option I have seen. Was this review helpful to you?

0 of 0 people found the following review helpful:

March 12, 2021 Reviewer: Anthony Neal from Asheville, NC United States   Great quality materials. Great Service. I will be looking to buy most of my brewing hardware here! Was this review helpful to you?

0 of 0 people found the following review helpful:

Awesome Product January 23, 2021 Reviewer: Wes I. from Knoxville, TN United States   I never knew a $15 upgrade to my kettle would make such a big difference. My old bulkhead was disagreeable- do I tighten it more? Do I put more Teflon tape on it? This one only has a washer on the outside, o-rings inside with a stationary hex. Easy to tighten, doesn't leak, and best of all, I don't have to use Teflon tape to get a seal. Bulkhead has attention to detail and  is absolutely perfect. Was this review helpful to you?

0 of 0 people found the following review helpful:

Fantastic upgrade! June 25, 2020 Reviewer: Joshua Ray from Lafayette, CO United States   I was using the option provided with my kettle and it always has felt unstable. This mounts perfectly and has such a lower profile. Was this review helpful to you?

0 of 0 people found the following review helpful:

November 9, 2018 Reviewer: JB Eid from Luling, LA United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Great quality October 27, 2018 Reviewer: michael johnson from crouse, NC United States   This is exactly what I needed for my rectangular cooler mash  tun. Does not leek and a quality product. Was this review helpful to you?

0 of 0 people found the following review helpful:

These are better than Bobby says July 12, 2018 Reviewer: Mike Dalecki from PLATTEVILLE, WI United States   Just added a couple of these to a kettle, and I'm just amazed at how good they are.  They are just as solid as welded bulkheads would be.  No play.  I had a weldless bulkhead fitting on a Northern Brewer kettle, and it was nothing like these.   I've always been anti-weldless for good reason, but these bulkheads are just the nuts.  I'm no longer anti-weldless, so long as I can use these. Was this review helpful to you?