Return to Flat Silicone Gasket for 1/2" NPT, bulkheads, LTS sight kits, etc (13/16" ID x 1.25 OD)

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 2

0 of 0 people found the following review helpful:

Gasket May 13, 2024 Reviewer: Anthony Scardaville from Bridgeville , DE United States   Well made gaskets! Was this review helpful to you?

0 of 0 people found the following review helpful:

A little tight but that's never a bad thing!!! September 15, 2023 Reviewer: Rumpleicious Brewing from NC   Had orings starting to leak and deform.  Read from others that these were a tight fit...and they are.  Put outer ring on and pulled outer edges while pushing down to seat.  Seemed that screwing the inner seal onto the post (after you pry it on) works best.  Keep turning until it is realatively close to the kettle walls.  I hand tightened the nut as much as possible and gave it about another turn with a large wrench. Filled pots up for testing and noticed 1. no leaks even while moving the valve around to simulate usage and 2. MUCH more stable feel to the valve.  Was kinda loose feeling before because the orings are so soft and you cant tighten them much w/o deforming the oring.  I put a fair bit of torque on these and NO deforming!  I ordered extra in case the tight fit causes wear but I'll take that thight fit over leaks on boil day anyday! Was this review helpful to you?

0 of 0 people found the following review helpful:

Great Quality December 21, 2020 Reviewer: Miguel Zavala from Villa Park, IL United States   The washers are of great quality, easy to use, and help prevent leaks.  Remember not to over tighten! Was this review helpful to you?

0 of 0 people found the following review helpful:

January 26, 2018 Reviewer: Patrick Rineman from Howell, MI United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Fits my needs perfectly September 9, 2017 Reviewer: Stephen Lamade from East Northport, NY United States   It's a known quality so I bought this as an extra because you never know when a project will come up in the future. Was this review helpful to you?

0 of 0 people found the following review helpful:

GASKET July 16, 2017 Reviewer: Dan F. from LOUISVILLE, KY United States   Worked great for my use - bulkhead fitting. Was this review helpful to you?

0 of 0 people found the following review helpful:

Seem very nice, a hair tight. May 16, 2017 Reviewer: Josh G. from Upstate, NY United States   I bought one to try out, they are well made but are a hair tight on the tapered 1/2" NPT fittings I have. They do fit but they'll probably get torn up after a while. I'm still going to buy more as the seal they make is far better than an o-ring. I'll just be sure to grab some spares. Was this review helpful to you?

0 of 0 people found the following review helpful:

Excellent service September 17, 2016 Reviewer: Binu Pillai from Santa Clarita, CA United States   They had all the stuff i needed for my mash tun.I received my stuff pretty quick also.Thanks guys !!! Was this review helpful to you?

0 of 0 people found the following review helpful:

Happy September 16, 2016 Reviewer: Ralph B from Sewickley., PA United States   Worked perfectly in my new color mash tun. Just what I needed to seal the opening tightly. Prompt delivery. Satisfied. Was this review helpful to you?

0 of 0 people found the following review helpful:

bought then as spare gaskets May 29, 2016 Reviewer: Philip Levin Slesarev from Tel Aviv, Dan Israel   bought then as spare gaskets Was this review helpful to you?