Return to Heating Element, Threaded, 1650 watt, 120v, All Stainless Steel

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 4

0 of 0 people found the following review helpful:

This thing is a beast! November 25, 2022 Reviewer: Jay Hager from Bend, OR United States   I use this to heat my mash water. No propane. No open garage door for ventilation. It's cold where I live and any time I can keep the doors closed it huge. With the Inkbird controller and this element I get a one deg. increase in temp every forty seconds. No more trouble maintaining mash temps. Was this review helpful to you?

0 of 0 people found the following review helpful:

Outstanding March 3, 2022 Reviewer: Joe P from MD United States   Outstanding item works perfectly I wouldn't hesitate to buy again Was this review helpful to you?

0 of 0 people found the following review helpful:

Great with the brewzilla 35l January 3, 2022 Reviewer: Goldie Bradley from Bucyrus, OH United States   This thing is great I run brewzilla with the 500 watt element and the hotrod heat stick  with 1650 watt elemnt. Cut heat up on half and the boil is great way better then just the 1500 total  from the brewzilla alone. Well made will buy more from bobby at brewhardware.com Was this review helpful to you?

0 of 0 people found the following review helpful:

Perfect wattage for my kettle March 29, 2021 Reviewer: Martin Landry from Québec, QC Canada   I turned my 8-gallon kettle into an electric kettle. I didn't want to hassle with any 240V electrical needs and instead ordered two 120V 1650W elements, which I plug on outlets from different breakers on my electrical panel. It works great. I use both together to raise my temperature with one plugged to my inkbird on one circuit and the second to a powerbar with an on and off switch on the other circuit. Once I have reached my desired temperature, either for boil, mash temperature or to mash out, I shut off the powerbar and the first one has enough power to maintain any temperature, even the boil. Couldn't be more pleased. Was this review helpful to you?

0 of 0 people found the following review helpful:

Very nice March 27, 2021 Reviewer: RW from Vancouver, BC   The warnings that these are not finished nicely to save the customer money are at first warranted. But it is very good quality and once I’d hooked it up and brewed it seemed the same as any over priced shiny element. Also if you want to scuff or sand the element there’s pretty stainless steel underneath. Great product, I’d buy again! Was this review helpful to you?

0 of 0 people found the following review helpful:

February 19, 2021 Reviewer: Adam Frey from West Chester, OH United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Works great! December 25, 2020 Reviewer: Jason from , Rhode Island   I have only brewed one beer so far with it, and I do 2.5 gallon batches, but worked great for me.  Took about 45-50 minutes to get to mash in temp and about the same to bring to boil.  The boil vigor was as expected, but much improved with partial covering (to allow for proper ventilation but also to keep some heat in).  Would buy again! Was this review helpful to you?

0 of 0 people found the following review helpful:

Great customer service! June 23, 2020 Reviewer: Brian   I reached out to Brew Hardware to ask about the element replacement on my HotRod Heatstick. Within a couple of hours I had a reply and made my purchase that night. Great customer service! Was this review helpful to you?

0 of 0 people found the following review helpful:

solid April 27, 2020 Reviewer: Odin Anderson from Bellevue, WA United States   solid build, easy to work with. Was this review helpful to you?

0 of 0 people found the following review helpful:

Works great! October 11, 2019 Reviewer: Fred from Seminole, FL United States   Stainless steel element was easy to install and works great. I’m keeping a spare handy! Was this review helpful to you?